Showing 81 through 89 out of 89 articles containing "glued up legs"
Paneled Window Seat
… (detail ‘b’). Work around the box until you end up back where you started. PANEL MOLDING. The panel molding (… the previous mitered pieces — one piece at a time, gluing and nailing as you go (details ‘a’ and ‘b’). LID MOLDING… wrapped base for a simple chamfer on the bottom of the “legs.” And the frame openings are covered with bead board. Finally, …Read More
Woodsmith Issue 153
June 2004
Corner Media Cabinet
… Blade tilted to 45° Cut to Depth. Get started by sneaking up on the depth of the rabbet …glued to case T BASE SIDE TRIM BASE FRONT TRIM (3!/2" x 43!/2") Legs LEG SUPPORT BLOCK (3!/2"x 3!/2"- #/4"-thick stock) a. b. !/4 Face frame rail Skirt filler !/16" roundover Leg R LEG SUPPORT BLOCK T #8 x #/4" Ph woodscrews SIDE SECTION VIEW Leg…Read More
Woodsmith Issue 154
August 2004
Sliding-Top Table
…made from #/4" plywood Inside corner of leg blank Leg !/16 B Drilling Guide. To make sure the screw holes line up in the sub-top and legs, make this simple drilling guide. 16… Size depth of rabbet so glass sets flush with frame H Veneer cut oversize before gluing Glass Caul Clamping Veneer Using Cauls. Use a couple layers of MDF to sandwich …Read More
Woodsmith Issue 171
June 2007
3-in-1 Bookcase
…the sides. During glue-up, these pieces will …up (detail ‘b’ below). Use a few screws to attach the bottom panel to the case before moving on to the leg assembly. a. LEG ASSEMBLY. The leg…legs are added (see Sources on page 51). The first step is to cut the plywood panel to size and for the Woodsmith tongues for the edge molding. After you’ve glued…Read More
Woodsmith Issue 175
February 2008
Box-Jointed Silverware Tray
…side assembly tip !/4 D E Cut dadoes for divider before assembling sides DIVIDER 5 Handle is glued to divider D 20˚ bevel on handle B c. A C Position fence flush with bearing C 2(/16 BOTTOM B …is captured in shallow dadoes centered on the short sides. You already have a leg up on this job. These 3⁄8"-wide dadoes can be cut with the dado …Read More
Woodsmith Issue 182
April 2009
Tips & Techniques
… 3#/4 TALL LEG BRACE NOTE: Push 10 block shown is built to fit right-tilt saw. Reverse this image for a left-tilt saw 3#/8 3&/8 4 Woodsmith No. 187 Flip-Up Stop Block A flip-up… to the handle with screws countersunk in the base. The cleat is glued on. HANDLE PATTERN 16!/2 One square = !/2" #/4"dia. 5!/4 Waste area #/4"dia. #/4"dia. You …Read More
Woodsmith Issue 187
February 2010
Shop Notebook
…clamp them in place beside and behind the leg. Finish up by securing the leg with a few strips of double-sided tape, …begins with a hardboard base and a pair of runners. Hardwood cleats are glued to the base at the front and rear to … pieces of hardwood glued together to form a 90° corner that points toward the front and backs up the cut. This gives…Read More
Woodsmith Issue 209
October 2013
Heavy-Duty Shop Workstation
… GUSSETS. The gusset pieces are angled to provide support for the legs when the workstation is assembled. I glued and clamped them in place on the rails to provide extra strength… a panel-cutting bench. Woodsmith.com • 39 Miter saw & planer TOOL STATIONS To set up your portable workstation for a miter saw or planer, all it takes is a platform …Read More
Woodsmith Issue 229
February 2017
Garden Tower
…fitting” portion of the process that’s coming up next. Each lattice strip is a different length. And due to the taper on the legs, they also have a different angle of …2 a. Quarter round END VIEW 1!/2" stainless steel finish nail Quarter round Quarter Round. Start by gluing and nailing the quarter round molding to two sides of the tower. Use …Read More
